Development of Draft Protocol for Testing of Structural Components and Systems

(a joint initiative of MoHUPA under technology submission of Pradhan Mantri Awas Yojna & IIT, KANPUR)

List of facilities available at different Institutes

Grp.No. S.No. Name of material Specification Name of Test Test IIT Kanpur
A 1. Common clay Bricks IS 1077-1992 Water Absorption Test IS 3495(1)-1992
2. Burnt Clay Fly ash Bricks IS 13757-1993 Water Absorption Test IS 3495(1)-1992
3. Burnt Clay Facing Bricks IS: 2691-1988 Compressive Strength IS 3495(2)-1992
Efflorescence Test IS 3495(3)-1992
Warpage IS 3495(4)-1992
4. Acid Resistant Bricks IS 4860-1968 Water Absorption Test IS 4860-1968
Compressive Strength IS 4860-1968
Flexural Strength IS 4860-1968
B 5. Cement IS 269-1989 Ordinary Portland Cement,Grade:33 Fineness IS 4031(1)-1996
IS 8112-2013 Ordinary Portland Cement, Grade:43 Consistency IS 4031(4)-1996
IS 12269-2013 Ordinary Portland Cement,Grade:53 Soundness IS 4031(3)-1996
IS 8042-1989 White Portland Cement Setting Time IS 4031(5)-1996
IS3466(b)-1988 Masonry Cement Compressive Strength IS 4031(7)-1996 for masonry IS 4031(6)-1966 for others
Specific Gravity IS 4031(11)-1996
6. Admixture IS 9103-1999 Workability(For Fresh Concrete) IS 1199-1959
Air Content(For Fresh Concrete) IS 1199-1959
Setting Time(For Fresh Concrete) IS 8142-1976
Bleeding(For Fresh Concrete) IS 9103-1999
Water Content(For Fresh Concrete) IS 9103-1999
Compressive Strength (For Hardened Concrete) IS 516-1959
Flexural strength IS 516-1959
Length Change IS 1199-1959
C 7. Sand for mortar IS 2116-1980(For Masonry Mortar) Sieve Analysis IS 2386(1)-1963
Deleterious Material IS 2386(2)-1963
Bulk Density IS 2386(3)-1963
Specific Gravity IS 2386(3)-1963
8. Sand for Plaster IS 1542-1992(For Plaster) Silt Content Test IS 2386(3)-1963
Deleterious Material IS 2386(2)-1963
Bulking of Sand IS 2386(3)-1963
9. Stone Chip/Coarse Aggregates IS 383-1970 Sieve Analysis IS 2386(1)-1963
Bulk Density IS 2386(3)-1963
Specific Gravity IS 2386(3)-1963
Water Absorption IS 2386(3)-1963
Impact Value IS 2386(4)-1963
Crushing Value IS 2386(4)-1964
Abrasion Value IS 2386(4)-1965
10% Fines Value IS 2386(4)-1966
Elongation Index IS 2386(1)-1963
Flakiness IS 2386(1)-1963
D 10. Fresh Concrete IS 456-2000 Air Content IS 1199-1959
Slump Test IS 1199-1959
Compaction Factor Test IS 1199-1959
Vee-bee Test IS 1199-1959
Flow Table Test IS 1199-1959
11. Concrete Blocks IS 2185(1)-2005 Water Absorption IS 2185(1)-2005
Compressive Strength IS 2185(1)-2005
Bulk Density IS 2185(1)-2005
12. Autoclaved Aerated Concrete Blocks IS 2185(3)-1984 Block Density IS 6441(1)-1972
Compressive Strength IS 6441(5)-1972
Thermal Conductivity IS 3346-1980
Drying Shrinkage IS 6441(2)-1972
13. Cement Concrete Cubes/Cylinders IS 456-2000 Compressive Strength IS 516-1959
Splitting Tensile Strength IS 5816-1999
Flexural Strength IS 516-1959
14. Non-destructive Testing(NDT) Core Compressive Strength IS 516-1959
Rebound Hammer IS 13311(2)-1992
Ultrasonic Pulse Velocity IS 13311(1)-1992
E 15. Steel for Reinforcement IS 1786-2008 Tensile Strength Test IS 1608-2005
Elongation Test IS 1608-2005
Bend Test IS 1599-2012
Re-bend Test IS 1786-1985
0.2% Proof Stress IS 1608-2005
16. Rolled Steel IS 2062-2011 Tensile Test IS 1608-2005
Bend Test IS 1599-2012
Impact Test IS 1757
Ygroove crackability Test  IS 10842
17. Steel Tubes for Structural Purpose IS 1161-1998 Tensile Test IS 1608-2005
Cold Bend Test IS 2329-2005
Flattening Test IS 2328-2005
18. Steel Chequered Plates IS 3502-2009 Tensile Test IS 1608-2005
Bend Test IS 1599-2012
F 19. Water for construction purpose IS 456-2000 Alkalinity Test IS 3025(23)-1986
Acidity Test IS 3025(22)-1986
Sulphates IS 3025(24)-1986
Chlorides IS 3025(32)-1988
Colour IS 3025(4)-1983
Taste IS 3025(8)-1984
Odour IS 3025(5)-1983
PH Value IS 3025(11)-1983
Total Solids IS 3025(18)-1988
Turbidity IS 3025(53)-2003
G 20. Precast Cement Concrete/Mosaic/ Terrazo Tiles IS 1237-2012 Water Absorption Test IS 1237-2012
Wet Transverse Strength IS 1237-2012
Resistance to Wear IS 1237-2012
21. Precast Cement Concrete Chequerred Tiles IS 13801-1993 Water Absorption Test IS 13801-1993
Wet Transverse Strength IS 13801-1993
Resistance to Wear IS 13801-1993
22. Glazed Tiles IS 15622-2006 Water Absorption Test IS 13630(2)-1993
Chemical Test IS 13630(8)-1993
Crazing Resistance IS 13630(9)-1993
Scratch Hardness on MOH’s Scale IS 13630(13)-1993
H 23. Marble Stone IS 1130-1969 Water Absorption Test IS 1124-1974
Scratch Hardness on MOH’s Scale IS 1124-1974
Apparent Specific Gravity IS 1124-1974
24. Kota Stone IS 1130-1969 Water Absorption Test IS 1124-1974
Scratch Hardness on MOH’s Scale IS 1124-1974
25. Sand Stone IS 3622-1977 Moisture Content IS 1124-1974
Compressive Strength IS 1121(1)-1974
Transverse Strength IS 1121(2)-1974
Tensile Strength IS 1121(3)-1974
Shear Strength IS 1121(4)-1974
Apparent Specific Gravity IS 1124-1974
26. Granite Stone IS 3316-1974 Moisture Content IS 1124-1974
Compressive Strength IS 1121(1)-1974
Apparent Specific Gravity IS 1124-1974
True Specific Gravity IS 1122-1974
I 27. Ply wood IS 303-1989 Moisture Content IS 1734(1)-1983
Glue Shear Strength in Dry State IS 1734(4)-1983
Resistance to water IS 1734(6)-1983
Adhesion of piles IS 1734(5)-1983
Compressive Strength IS 1734(10)-1983
Tensile Strength IS 1734(9)-1983
28. Teak Wood IS 15457- 2004 Test for Defects IS 15457- 2004
Measurement of Girth IS 15457- 2004
29. Door, Window and Ventilator Frames IS 4021- 1995 Materials IS 4021- 1995
Dimensions and Tolerances IS 4021- 1995
Workmanship and Finish IS 4021- 1995
30. Flush Door Shutter (Solid Core Type) IS 2202(1)-1991 Dimensions and Squareness Test IS 4020(2)-1998
IS 2202(2)-1991 General Flatness Test IS 4020(3)-1998
31. (Cellular and Hollow Core Type) IS 2191(1)-1983 Local Planeness Test IS 4020(4)-1998
IS 2191(2)-1983 Impact Indentation Test IS 4020(5)-1998
Flexure Test IS 4020(6)-1998
Edge Loading Test IS 4020(7)-1998
Shock Resistance Test IS 4020(8)-1998
Buckling Resistance Test IS 4020(9)-1998
Slamming Test IS 4020(10)-1998
Misuse Test IS 4020(11)-1998
Varying Humidity Test IS 4020(12)-1998
End Emersion Test IS 4020(13)-1998
Knife Test IS 4020(14)-1998
Glue Adhesion Test IS 4020(15)-1998
Screw Withdrawal Resistance Test IS 4020(16)-1998
32. Wire Guaze Shutter IS 1003(1)-2003 (for door shutter) Dimensions and Squareness Test IS 4020(2)-1998
General Flatness Test IS 4020(3)-1998
Local Planeness Test IS 4020(4)-1998
Impact Indentation Test IS 4020(5)-1998
Flexure Test IS 4020(6)-1998
Edge Loading Test IS 4020(7)-1998
Shock Resistance Test IS 4020(8)-1998
Buckling Resistance Test IS 4020(9)-1998
Slamming Test IS 4020(10)-1998
Misuse Test IS 4020(11)-1998
Screw Withdrawal Resistance Test IS 4020(16)-1998
IS 1003(2)-1994 (for window shutter) Slamming Test IS 1003(2)-1994
IS 1568-1970 (for wire cloth) Test for Dimension IS 1568-1970
33. Glass Fibre Reinforced Plastic(FRP) Door Shutter IS 14856- 2000 Dimensions and Squareness Test IS 4020(2)-1998
General Flatness Test IS 4020(3)-1998
Local Planeness Test IS 4020(4)-1998
Impact Indentation Test IS 4020(5)-1998
Edge Loading Test IS 4020(7)-1998
Shock Resistance Test IS 4020(8)-1998
Buckling Resistance Test IS 4020(9)-1998
Slamming Test IS 4020(10)-1998
Misuse Test IS 4020(11)-1998
34. Steel doors,windows and ventialtors IS 1038-1983 Dimensions and Tolerances IS 1038-1983
Materials IS 1038-1983
Fabrication IS 1038-1983
Positioning of holes, fixing screws and lugs IS 1038-1983
Finish IS 1038-1983
Glazing IS 1038-1983
35. Steel Door Frames IS 4351-2003 Dimensions and Tolerances IS 4351-2003
Materials IS 4351-2003
Construction IS 4351-2003
Base Ties IS 4351-2003
Fittings IS 4351-2003
Finish IS 4351-2003
36. Door Handles IS 208: 1996 Dimensional Requirement IS 208: 1996
Finish IS 208: 1996
37. Door Stopper IS 1823: 1980 Relative Density IS: 3400 (part 9)-1978
J 38. Veneered Particle Board IS 3097-2006 Density IS 2380(3)-1977
Moisture Content IS 2380(3)-1977
Water Absorption Content IS 2380(16)-1977
Swelling due to general absorption IS 2380(17)-1977
Swelling due to surface absorption IS 2380(17)-1977
Water Resistance Test IS 3097-2006
Adhesion of piles IS 3097-2006
Modulus of Elasticity and Modulus of Rupture IS 2380(4)-1977
Determination of Deflection under Sustained Loading IS 2380(13)-1977
39. Prelaminated Particle Board IS 12823-1990 Density IS 2380(3)-1977
Moisture Content IS 2380(3)-1977
Water Absorption Content IS 2380(16)-1977
Swelling due to general absorption IS 2380(17)-1977
Modulus of Rupture IS 2380(4)-1977
Test for Tensile Strength Perpendicular to Surface IS 2380(5)-1977
Test for Tensile Strength Perpendicular to Surface(after ageing) IS 2380(5)-1977
Screw Withdrawal Resistance Test IS 2380(14)-1977
Abrasion Resistance IS 12823-1990
Crack Resistance IS 12823-1990
Resistance to Steam IS 12823-1990
Resistance to Cigarette Burn IS 12823-1990
Resistance to Stain IS 12823-1990
40. Cement Bonded Particle Board IS 14276-1995 Accuracy of Dimensions of Boards IS 2380(2)-1977
Density IS 2380(3)-1977
Moisture Content IS 2380(3)-1977
Water Absorption Content IS 2380(16)-1977
Swelling due to general absorption IS 2380(17)-1977
Screw Withdrawal Resistance Test IS 2380(14)-1977
Test for Tensile Strength Perpendicular to Surface IS 2380(5)-1977
Modulus of Elasticity and Modulus of Rupture IS 2380(4)-1977
41. Low Density Fibre Board IS 3129-1985 Accuracy of Dimensions of Boards IS 2380(2)-1977
IS 3087-2005 Density IS 2380(3)-1977
IS 3478-1966 Moisture Content IS 2380(3)-1977
Transverse Strength IS 2380(4)-1977
Water Absorption Content IS 2380(16)-1977
Swelling due to general absorption IS 2380(17)-1977
Test for Tensile Strength Perpendicular to Surface IS 2380(5)-1977
Swelling due to surface absorption IS 2380(17)-1977
Screw withdrawal strength test IS 2380(14)-1977
Boiling Water resistance Test IS 3478-1966
42. Medium Density Fibre Board IS 12406-2003 Density IS 2380(3)-1977
Moisture Content IS 2380(3)-1977
Water Absorption Content IS 2380(16)-1977
Linear Expansion Swelling IS 2380(17)-1977
Test for Modulus or Elasticity and Modulus of Rupture IS 2380(4)-1977
Test for Internal Bond IS 2380(5)-1977
Test for Screw Withdrawal Strength IS 2380(14)-1977
43. High Density Fibre Board IS 1658-2006 Dimensions and Tolerances IS 1658-2006
Density IS 1658-2006
Moisture Content IS 1658-2006
Water Absorption Content IS 1658-2006
Test for Swelling in Thickness After Immersion in Water IS 1658-2006
Tensile Strength Perpendicular to the Plane of the Board (Internal Bond Strength) IS 1658-2006
Modulus of Elasticity and Modulus of Rupture IS 1658-2006
44. Gypsum Board IS 2095(1)-1996 Mass Determination IS 2542-1981
IS 2095(2)-1996 Transverse Strength IS 2542-1981
IS 2095(3)-1996 Compressive Strength IS 2542-1981
Thermal Conductivity IS 9489-1980
Jolting Test IS 2095(3)-1996
Free Moisture IS 2542(2)-1981
Surface Hardness Test IS 2095(3)-1996
Water Absorption IS 2380(16)-1977
Swelling IS 2380(17)-1977
45. Block Board IS 1659-2004 Test for thickness and variation in thickness IS 1659-2004
Resistance to water IS 1659-2004
Adhesion of piles IS 1659-2004
Modulus of Elasticity IS 1659-2004
Modulus of Rupture IS 1659-2004
Spot Test IS 1659-2004
J 46. Steel Butt Hinges IS 1341-1992 Dimensions and Tolerances IS 1341-1992
Manufacture IS 1341-1992
Finish IS 1341-1992
47. Continous(Piano) Hinges IS 3818-1992 Dimensional Requirement IS 3818-1992
Manufacture IS 3818-1992
Finish IS 3818-1992
48. Double Acting Spring Hinge IS 453-1993 Dimensional Requirement IS 453-1993
Manufacturing Defects IS 453-1993
Finish IS 453-1993
49. Tower Bolts IS 204(1)-1991 (for ferrous metals) Dimensional Requirement and Finish IS 204(1)-1991
IS 204(2)-1992 (for non-ferrous metals) Dimensional Requirement and Finish IS 204(2)-1992
50. Stays and Fasteners IS 10019-1981 Shape and Size IS 10019-1981
Defects in Manufacture IS 10019-1981
Finish IS 10019-1981
Performance Test IS 10019-1981
K Electroplated Zinc Coating IS 1573-1986
51. GI pipes and Fittings IS 1239
52. GI Sheets IS 277-2003 Hot Dipped Galvanized Coatings IS 4826-1979
53. Barbed Wires IS 278-2009 Breaking Load IS 1608-2005
IS 280-2006 Diameter of Wire IS 278-2009
Thickness of Sheet IS 280-2006
54. Aluminium IS 1868-1996 Thickness of Anodic Coating IS 5523-1983
L 55. Integral waterproofing compounds for cement mortar and concrete IS 2645:2003 Permeability to water IS 2645:2003
Setting Time IS 4031(5)-1996
Compressive Strength IS 4031(6)-1966
Chloride Content IS 6925-1973
56. Bitumen felt for waterproofing IS 1322:1993 Breaking Strength IS 13826(1)-1993
Pliability Test IS 13826(2)-1993
Srorage Sticking Test IS 13826(3)-1993
Pressure Head Test IS 13826(4)-1993
Heat Resistance Test IS 13826(5)-1994
Water Absorptionn Test IS 13826(6)-1993
Binder Content Test IS 13826(7)-1993
57. Bitumen primer for waterproofing IS 3384-1986 Penetration Test IS 1203-1978
Softening Point IS 1205-1978
Ductility Test IS 1208-1978
Flash Point and Fire Point IS 1209-1978
M 58. Precast Concrete Manhole Cover and Frame IS 12592-2002 Dimensions IS 12592-2002
Load Test IS 12592-2002
59. Cast Iron Manhole Cover and Frame IS 1726-1991 Dimensions IS 1726-1991
Load Test IS 1726-1991
N 60. Bitumen and Tar(80/100) IS 73-2013 Specific Gravity IS 1202-1978
Penetration Test IS 1203-1978
Softening Point IS 1205-1978
Ductility Test IS 1208-1978
Flash Point and Fire Point IS 1209-1978
61. Bitumen(85/25) IS 702-1988 Marshall Stability ASTM D 1559
Specific Gravity IS 1202-1978
Penetration Test IS 1203-1978
Ductility Test IS 1208-1978
Flash Point and Fire Point IS 1209-1978
O 62. Pillar taps IS 1795-1982 Materials IS 1795-1982
Dimensions IS 1795-1982
Hydraulic  pressure  test IS 1795-1982
63. Water Closet IS 7231:1994 Materials IS 7231:1994
Dimensions IS 7231:1994
Working Water Level IS 7231:1994
Test for Discharge Capacity IS 7231:1994
Test for Discharge Rate IS 7231:1994
Endurance Test IS 7231:1994
Distortion Resistance IS 7231:1994
Dead Load Test IS 7231:1994
Front Thrust Test IS 7231:1994
Impact Test IS 7231:1994
64. Squatting Pans IS 2556 (Part 3) :2004 General Requirements IS 2556 (Part 1) :1994
Dimensions IS 2556 (Part 3) :2004
Toilet Paper Test IS 2556 (Part 3) :2004
Smudge Test IS 2556 (Part 3) :2004
Water Holding Capacity Test IS 2556 (Part 3) :2004
Saw Dust Test IS 2556 (Part 3) :2004
Splash Test IS 2556 (Part 3) :2004
Sampling and Inspection IS 9140:1996
65. Shower Rose IS 2556(Part-7): 1995 General Requirements IS 2556 (Part 1) :1994
Dimensions IS 2556(Part-7): 1995
Tolerance IS 2556(Part-1): 1995
66. Kitchen Sink (Stainless Steel) IS 13983:1994 Materials IS 5522:1992
Dimensions IS 13983:1994
Visual examination IS 13983:1994
67. Wash Basins IS 2556 (Part 4) :2004 General Requirements IS 2556 (Part 1) :1994
Dimensions IS 2556 (Part 4) :2004
Load Bearing Test IS 2556 (Part 4) :2004
Sampling and Inspection IS 9140:1996
68. Cast Iron Brackets and Supports for Wash Basin IS 775:1970 Materials IS 210:2009
Dimensions IS 775:1970
Minimum Weight IS 775:1970
69. Unplasticized Polyvinyl Chloride (Upvc) Single Wall Corrugated Pipes For Drainage IS 9271:2004 Materials IS 4669:1968
Dimensions IS 9271:2004
Density IS 9271:2004
Pipe Stiffening IS 9271:2004
Impact Strength at 0°C IS 9271:2004
Elongation Test IS 9271:2004
Bending Test: IS 9271:2004
Strength of Joints IS 9271:2004
70. Ball Valves IS 9890:1981 Materials IS 9890:1981
End Connection IS 554:1999
Drain Connection IS 9884:1981
Test IS: 6157-1981
Marking IS 9866:1981
71. Bends with Fittings IS 10124 (part 1) Materials IS 4985:2000
Size IS 4985:2000
Dimensions IS 10124 (part 1)
Opacity Test IS 12235 (part 3)
Short Term Hydraulic Test IS 10124 (part 1)
72. Single Taps, Combination Tap Assembly and Stop Valves, Bib Cock IS 8931:1993 Materials IS 8931:1993
Dimensions IS 8931:1993
Performance Test IS 8931:1993
Pressure Resistance Characteristic IS 8931:1993
Hydraulic Characteristic IS 8931:1993
Mechanical Strength Characteristics IS 8931:1993
Sampling IS 8931:1993
73. Cast Iron Manhole Cover and Frame IS 1726:1991 Dimensions IS 1726:1991
Load Test IS 1726:1991
Sampling IS 1726:1991
74. Gate Valves IS 778:1984 Dimensions IS 778:1984
Body Test IS 778:1984
Back Seat Test IS 778:1984
Seat Test IS 6157:1971
75. GI Pipes Fittings and Union IS 1239 (part 1) Dimensions IS 1239 (part 1)
IS 1239 (part 2) IS 1239 (part 2)
Leak Proof Test IS 1239 (part 1)
Tensile Strength IS 1608
IS 12278
Bend Test IS 2329
Flattening Test IS 2328
Re Test IS 1239 (part 1)
Expansion Test for Sockets IS 2335
Pressure Test IS 1239 (part 2)
Sampling IS 4711
Mass of Zinc Coating IS 4736
Uniformity of Zinc Coating IS 2633
Adhesion Test IS 2629
76. Glazed Stoneware Pipes and Fittings IS 651:2007 Dimensions IS 651:2007
Hydraulic Test IS 651:2007
Absorption Test IS 651:2007
Test for Acid Resistance IS 651:2007
Test for Alkali Resistance IS 651:2007
Crushing Strength Test IS 651:2007
77. Gratings for Drainage IS 5961:1970 Dimensions IS 5961:1970
Load Test IS 1726:1991
78. PVC Corrugated Pipes IS 9271:2004 Materials IS 4669
Dimensions IS 9271:2004
Impact Strength IS 9271:2004
Elongation Test IS 9271:2004
Bend Test IS 9271:2004
Testing of Joints IS 9271:2004
Sampling IS 4905
79. Precast RCC Pipes IS 458:2003 Dimensions IS 458:2003
Hydrostatic Test IS 3596
Three-edge Bearing Test IS 3596
Permeability Test IS 3596
80. Traps IS 5219:1969 Dimensions IS 5219:1969
Materials IS 292:1983
81. Unplasticised PVC Pipes for Potable Water IS 4985:2000 Dimensions IS 4985:2000
Opacity Test IS 12235 (part 3)
Effect on Water IS 12235 (part 4)
IS 12235 (part 10)
IS 12235 (part 11)
Reversion Test IS 12235 (part 5)
Vicat Softening Temperature IS 12235 (part 2)
Density IS 12235 (part 14)
Sulphated Ash Content IS 4985:2000
Hydrostatic Characteristic IS 12235 (part 8)
Resistance to External Blows IS 4985:2000
82. Transparent Float Glass IS 14900:2000 Thickness IS 14900:2000
Length and Width IS 14900:2000
Bubbles IS 14900:2000
Foreign Matter IS 14900:2000
Reams, Strings and Lines IS 14900:2000
Scratch, Rubs and Crush IS 14900:2000
 Squareness IS 14900:2000
83. Flat Transparent Sheet Glass IS 2835:1987 Dimensions IS 2835:1987
Thickness IS 2835:1987
Intensity of Reams, Strings and lines IS 2835:1987
Bows IS 2835:1987
Intensity of Scratches, Rubs and Crush IS 2835:1987
84. UPVC pipe fittings IS 13593: 1992 Hydrostatic Test IS 12235 (Part 8): 1986
Vacuum Test IS 13593: 1992
85. PVC-U pipe for waste drainage IS 13592: 2013 Visual Appearance IS 13592: 2013
Reversion Test IS: 12235 (Part 5)
Stress Relief Test IS: 12235 (Part 6)
Vicat Softening Temperature IS: 12235 (Part 2)
Resistance to Dichloromethane IS: 12235 (Part 11)
Tensile Test IS: 12235 (Part 13)
Resistance to sulphuric acid IS: 12235 (Part 7)
Impact Test IS: 12235 (Part 9)
Axial Shrinkage IS 13592: 2013
86. PVC flooring IS 3462: 1986 Color and finish IS 3462: 1986
Dimensions and tolerances IS 3462: 1986
Dimensional stability IS 3462: 1986
Moisture movement IS 3462: 1986
Curling IS 3462: 1986
Heat ageing and exudation IS 3462: 1986
Resistance to various Substances, IS 3462: 1986
Flexibility IS 3462: 1986
Elastic product IS 3462: 1986
87. Tees IS 8360(part 2): 1977 Hydaulic Proof Test IS 8360(part 2): 1977
Dimensions IS :4984-1972
88. Copper fittings  IS: 2963-1979 Dimensions  IS: 2963-1979
Criteria for Conformity  IS: 2963-1979
89. Putty for window frames IS 419: 1967 The calcium carbonate content IS: 419: 1967
Residue on sieve IS: 101 (part 8)- 1989
Water Content IS: 101 (part 2)- 1988
90. Putty for Structural purpose ASTM C1489 Chemical Analysis ASTM C25
Physical Analysis ASTM C110
91. Rubber Seal Ring IS : 5382-1985 Hardness IS : 3400 ( Part 2) – 1980
tensile strength and elongation at break IS: 3400 ( Part 1 ) – 1977
compression set IS: 3400 ( Part 10 )-1977
Accelerated ageing in air IS : 3400 ( Part 4 )-1978
water immersion IS : 3400 ( Part 6 )-1983
Stress Relaxation in Compression IS : 5382-1985
Cold Resistance IS : 5382-1985
water absorption IS : 5382-1985
92. Socket, Spigot and Bat Clamps IS 1729: 2002 Hardness IS: 1500- 2005
Hammer Test IS 1729: 2002
Leakage Test IS 1729: 2002
93. Glass Mirrors IS 3438: 1994 Test for waviness IS 3438: 1994
Salt spray Test IS 3438: 1994
Hot water Test IS 3438: 1994
Testing of Copper and Silver Plating IS 3438: 1994
94. Chlorpyrifos IS 8944: 2005 Quality of Reagents IS: 1070-1992
Cold Test IS 6940
Flash Point IS 1448 [Part: 20]
Emulsion Stability IS 6940
Chlorpyrifos Content IS 8963:2006
Acidity Test IS 6940
95. Hasp and Staples IS 363: 1963 Dimensions IS 363: 1963
Manufacturing Defects IS 363: 1963
Finish IS 363: 1963
96. Hooks IS 9899: 1981 Dimensions IS 9899: 1981
Manufacturing Defects IS 9899: 1981
Finish IS 9899: 1981
97. Lindane IS 632: 1978 Cold Test IS 6940
Flash Point IS 1448 [Part: 20]
Emulsion Stability IS 6940
Gamma-Isomer Content IS: 561-1978
Acidity Test IS 6940
Quality of Reagents IS: 1070-1992
98. Rolling Grills IS:  6248 -1979 Materials IS:  6248 -1979
99. Welded Steel wire Mesh IS 4948: 2002 Manufacture IS 4948: 2002
Test for Welding IS 4948: 2002
Test for wire IS 4948: 2002
100. Plastic Emulsion Paint IS 15489: 2004 Determination of Opacity IS 15489: 2004
Durability IS 15489: 2004
Determination of Drying Time and Finish IS 15489: 2004
 Determination of Colour IS 15489: 2004
Resistance to Alkali IS 15489: 2004
Washability and Cleanability, IS 15489: 2004
Stability Test IS 15489: 2014
Quality of Reagents IS: 1070-1992
101. Enamel Paint IS 133: 2004 (interior) Drying Time IS: 101 (part 3/ sec 1)
IS 2932(exterior) Flash point IS: 101 (part 1/sec 6)
Resistance to Alkali IS 2932
Resistance to Acid IS 2932
Viscosity by ford cup IS: 101 (part 1/sec 5)
Fineness IS: 101 (part 3/sec 5)
wet opacity IS: 101 (part 4/sec1)
Accellerated Storage stabiity IS 133: 2004 (interior)
water content IS: 2932-2003(exterior)
Resistance to water IS 133: 2004 (interior)
Flexibilty and Adhesion IS 133: 2004
Color IS: 101 (part 4/sec 2)
Scratch Hardness IS: 101 (part 5/sec1)
102. Washable Distemper IS 428: 2013 Drying Time IS 428: 2013
Consistency IS 428: 2013
Residue on sieve IS 428: 2013
Recoating Properties IS 428: 2013
Resistance to Alkali IS 428: 2013
Accelerated storage stability IS 428: 2013
Quality of Reagents IS: 1070-1977
103. Lime for White wash IS 712: 1984 Calcium and Magnesium oxide percent IS: 6932 (part 1)-1973
Silica, Alumina and ferric oxide percent IS: 6932 (part 1)-1973
Unhydrated magnesium oxide percent IS: 6932 (part 5)-1973
Insoluble residue in dilute acid and alkali IS: 6932 (part 1)-1973
Carbondioxide percent IS: 6932 (part 2)-1973
Free Moisture IS: 1514-1990
Available Lime IS: 1514-1990
Fineness IS: 6932 (part 4)-1973
Residue on slaking IS: 6932 (part 3)-1973
Setting Time IS: 6932 (part 11)-1973
Compressive strength IS: 6932 (part 7)-1973
Transverse Strength IS: 6932 (part 7)-1973
Workability IS: 6932 (part 8)-1973
Volume Yield IS: 6932 (part 6)-1973
Soundness IS: 6932 (part 9)-1973
Popping and pitting IS: 6932 (part 10)-1973
104. Distemper IS 427:2013 Quality of Reagents IS: 1070-1977
Form and Condition IS: 427-2013
Drying time, Hard dry IS: 427-2013
Consistency IS: 427-2013
Finish IS: 101 (Part 3/Sec 4)
Colour IS: 101 (Part 4/Sec 2)
Fastness to Light IS: 101 (Part 4/Sec 3)
Residue on Sieve IS: 427-2013
Recoating Properties IS: 427-2013
Resistance to Alkali IS: 427-2013
Resistance to dry rubbing IS: 427-2013
Lead Restriction IS: 101 (Part 4/Sec 3)
Application IS: 427-2013
Keeping Propertiees IS: 427-2013
105. Cement Concrete Flooring IS 2571:1970 Materials IS 2571:1970
Panel Dimension IS 2571:1970
Adhesion to the Base or Sub-floor IS 2571:1970
Minimum Thickness IS 2571:1970
Lugs IS 4351:2003 Materials IS 513
IS 277
Dimensions IS 4351:2003
Finish IS 2074
Newsfeed